• Visit https://www.embeddedcomputers.net/ for Hardware; Software and all other things related to FlashcatUSB

SBG900 Script

I am going to see if we can get hold of this device to finally resolve any issues with it may have.
 
this
 

Attachments

  • SBG900.BPI.OK._.Consola.rar
    2.9 MB · Views: 21
  • SBG900.BPI.OK._.Consola.rar
    2.9 MB · Views: 11
No news yet , still trying to procure one of these devices.
 
Try this script now , i have found where my error was , you may get a few mismatches towards the end , but do not let this bother you as it is only the logs.
Hopefully this will resolve your issue.
 

Attachments

  • SBG900_JTAG.bcs
    7 KB · Views: 9
i tried using this script and the modem still bricked!

and when i choose the firmware in the sbg900 tab it install it in less than 1 sec.. what do i have to do?
 
Did you use the CFI tab to load a full dump ? and did you get any mismatch errors whilst doing this ?
I am working on the tabs of the script , seems there may be another issue i have overlooked .
 
Try this script , think i have the image tabs and bootloader fixed.
 

Attachments

  • SBG900_JTAG.bcs
    7 KB · Views: 7
Try this script and let me know.

Forget this ,, there still seems to be an issue , let me get back to you on this.
 

Attachments

  • SBG900_JTAG.bcs
    6.8 KB · Views: 14
d3mon i dont know if my modem is bricked and i cant use it anymore! i will buy another one to check if its the modem or the script! because still doing the same, 3 lights, 10 seconds then all off
 
It is actually a problem in the software , i am trying to find a new coder at the present time to resolve this issue.
I found with the 900 i have that if i write the original flash back to the device it programs ok , but the minute i try to flash something different it mismatches.
I am going to try and delete the flash and see if it will program ok that way with no other data present. This is just until i can get someone to look at the code.
 
i wanted to install a fresh virgin flash to one of this i own.. it was working excepts by mistake i ran some telnet commands which disabled completely access to telnet... i downloaded a couple of backup which were made by jtagnt... also there is a flash which has telnet enabled that has 4 MB i tried to flash that... and all i got is a bricked modem.
tried also some of the jtagnt that has firm, cfg and bootloader.. nothing.. those backup don't have a flash of 8 MB neither memory of 8 MB. the memory size those backup has is a 16 MB bin

i made a backup before playing with that.. and it's useless, also made a backup of firm1 and 2 i recovered both modem still dead.. 3 light for some seconds and all off. i believe i still have hope of recovering this.. there are some commands to use with old black cat and tom's jtag utility.. but never detect my flash.

any ideas ?? do you have a good working backup of 8 MB size?

i tried the script because was posted in general area.. i thought it was completlely working for general use.. but i gues is not...

it's failing to write correctly since all data verification always return failed.

i got PCB 1.2 and FCUSB.RC15.330
 
There is an issue with this device as you can see from this thread , i am working on trying to get it resolved.
 
i'm glad you're trying to fix this issue, my only hope is blackcat usb by now.. y tried with classic blackcat to debrick it and didn't detect the device.
i was thinking to buy jtagnt but if recive good support with my old pcb 1.2 i would prefer to buy soon pcb 1.8 or newer

My Best Regards
 
USBJTAGNT is by far the best device on the market , you can not go wrong by getting one of these.
My issue in getting FCUSB to work to a good standard is trying to find a coder that can help me with the code. That is why it is taking forever to get things sorted.
 
Back
Top